Industrial Plasma Cutting Table, 1500 × 3000 mm
This industrial CNC plasma table takes standard 1500 × 3000 mm plate, with custom bed sizes on request. With a 65–200 A Hypertherm or Chinese-brand source it cuts 0.5 to 30 mm carbon steel, stainless steel and aluminum at up to 15,000 mm/min. A dual-drive Y axis, helical rack and digital torch height control keep parts accurate across the whole bed.
- 1500 × 3000standard bed, mm
- 0.5–30 mmcutting thickness
- 65–200 Aplasma source
- ±0.03 mmrepositioning
Specifications
Swipe the table sideways to see all columns.
| Parameter | Industrial plasma table |
|---|---|
| Working area | 1500 × 3000 mm standard; custom sizes available |
| Z-axis travel | 200 mm |
| Cutting thickness | 0.5–30 mm, depending on the plasma source |
| Plasma source | 65–200 A, Hypertherm or Chinese brands |
| Max travel speed | 15,000 mm/min |
| Repositioning accuracy | ±0.03 mm |
| Control system | Starfire, Fangling or DSP |
| Drive | Precision stepper or servo motors, dual-drive Y axis |
| Transmission | High-precision helical rack and pinion |
| Torch height control | Digital arc-voltage THC, standard |
| Frame | Welded heavy square tube, stress-relieved |
| Table type | Water table or down-draft exhaust |
| Software | Built-in shape library; G-code from FastCAM and other nesting software |
Built for full shifts on standard plate
Stress-relieved frame
The bed is welded from heavy square tube and stress-relief tempered, so it stays flat and free of vibration during fast nesting moves.
Dual-drive Y axis
A motor on each side of the gantry keeps it square at speed, so long parts on a 3 m bed come out straight.
Digital arc control
The THC monitors arc voltage in real time and follows warped plate, which keeps bevel angle and dross consistent.
Shapes without a PC
The multilingual control has a built-in shape library, so operators can cut flanges, rings and rectangles directly at the machine.
Less scrap
Nesting software lays parts out automatically; shops typically use up to 15% less plate than with manual layouts.
Custom bed sizes
Need 2000 mm width or a 4 m or 6 m bed? We build the table to your plate size. For plate wider than 2 m, see the gantry machines.
Water table or down-draft table?
Water table
- Water under the plate catches sparks and dust at source
- Lower cost, no large fan needed
- Cools the parts and reduces warping on thin sheet
- Needs the water changed and sludge cleaned out
Down-draft exhaust
- Zoned fan extraction pulls smoke down through the table
- Parts stay dry, which suits painting and powder coating
- Better for high-volume production indoors
- Needs a fan and a filter or outside duct
Choose the plasma source
Sources from 65 A to 200 A cover most fabrication work on this table. Hypertherm gives the best edge quality and consumable life; Chinese brands lower the purchase price.
Swipe the table sideways to see all columns.
| Plasma current | Good-quality cut (edge start) | Production pierce | Typical work |
|---|---|---|---|
| 63–65 A | up to 16–20 mm | about 10 mm | General sheet metal |
| 85 A | up to 20–25 mm | about 12–16 mm | Brackets, base plates |
| 100–105 A | up to 25–32 mm | about 16–20 mm | Fabrication shops |
| 120–125 A | up to 32–38 mm | about 20–25 mm | Thicker structural plate |
| 200 A | up to 50 mm | about 30–32 mm | Heavy plate on gantries |
Typical guidance for mild steel. Stainless steel and aluminum cut thinner. Capacity differs between plasma brands, so we confirm it for the source on your quotation. CNC parts usually start with a pierce, which is roughly half to two thirds of the edge-start thickness.
What your workshop needs
- Electrical supply: 3-phase 380 V or your local industrial voltage. Tell us your local voltage and frequency (50 or 60 Hz) before we build the machine.
- Clean, dry compressed air: an air compressor with a refrigerated dryer and filters. We give the flow and pressure for the plasma source you choose.
- A level concrete floor and space to load full sheets with a forklift or crane.
- Fume control: a water table or a down-draft table with an extraction fan, depending on the model.
- A Windows PC for nesting software such as FastCAM, to turn DXF drawings into cutting programs.
Shipping, installation and support
Free production layout
Send your parts list or shop drawing and our engineers suggest the machine size, plasma source and table layout before you order.
Packed for sea freight
Machines are packed for container shipping. We quote to your nearest port in South America, Africa or elsewhere and prepare the export documents.
Installation and training
Remote installation guidance and operator training are included. On-site commissioning can be arranged.
Remote diagnostics
Our team supports the control, the plasma source and the nesting software remotely, so most problems are solved without waiting for a visit.
Get a configuration and price
Send the material, the thickest plate or largest pipe you cut, your sheet or pipe size and how many hours a day the machine will run. An engineer replies with the right table size and plasma source, the options and a price delivered to your port.
Frequently asked questions
Which plasma power sources can I choose?
65 A to 200 A, from Hypertherm or leading Chinese brands. We size the source to the thickest plate you cut every day.
What is the standard working area?
1500 × 3000 mm. Custom lengths and widths are available; for plate wider than about 2 m a gantry machine is usually the better choice.
How thick can it cut?
0.5 mm to 30 mm, depending on the plasma source. With 200 A it cuts up to 30 mm with good quality.
Which control systems are available?
Starfire, Fangling or DSP. The Starfire and Fangling controls have a built-in shape library and run G-code from FastCAM and other nesting software.
Is torch height control standard?
Yes. A digital arc-voltage THC is standard and compensates for warped plate in real time.
How is this different from the P1530?
Both take 1500 × 3000 mm plate. This table is the general-purpose model with a water or down-draft table. The P1530 has a reinforced monoblock frame, a Hypertherm source and an oxy-fuel torch for plate up to 200 mm.
Related machines and guides
Last updated 15 October 2026. Specifications are for standard configurations and can change with options; confirm on your quotation.