P1530 CNC Plasma Cutter with Oxy-Fuel
The P1530 is our heavy-duty table for 1500 × 3000 mm (5 × 10 ft) plate. A Hypertherm plasma system cuts steel up to 40 mm, and an oxy-fuel torch on the same machine cuts 6 to 200 mm plate. The reinforced monoblock frame is stress-relief annealed and then precision machined, so it keeps its accuracy under the heat of high-amperage cutting.
- 1500 × 3000cutting area, mm
- Up to 40 mmplasma, steel
- 6–200 mmoxy-fuel
- Hyperthermplasma system
Specifications
Swipe the table sideways to see all columns.
| Parameter | P1530 |
|---|---|
| Effective cutting area | 1500 × 3000 mm (5 × 10 ft) |
| Plasma system | Hypertherm |
| Plasma cutting capacity | Up to 40 mm steel |
| Oxy-fuel cutting capacity | 6–200 mm steel |
| Frame | Reinforced monoblock: heavy square tube and thick steel plate |
| Frame treatment | Stress-relief annealing, then precision machining |
| Torch height control | Automatic arc-voltage THC for plasma |
| Nesting software | FastCAM or StarCAM |
Plasma source size, control and drive are matched to your plate and confirmed on your quotation.
Two processes on one table
Plasma
- Fast cutting from thin sheet up to 40 mm
- Narrow kerf and small heat-affected zone
- Best for parts with holes and fine detail
- Hypertherm source for clean edges and long consumable life
Oxy-fuel
- Cuts 6 mm up to 200 mm carbon steel
- Low running cost on thick plate
- Square edges on heavy base plates and flanges
- Carbon steel only; plasma cuts stainless and aluminum
Why the heavier frame matters
Lighter desktop tables can twist when hot, thick plate sits on them for hours. The P1530 frame is built as one reinforced monoblock from heavy square tube and thick plate, annealed to release welding stress and then machined, so the rails stay straight and parts stay to size on long production runs.
Typical work
Heavy steel fabrication
Base plates, gussets, flanges and lifting lugs from 10–40 mm plate.
Agricultural machinery
Frames, hitches and wear parts in mild steel.
Large signage
Big letters and panels that need the full 5 × 10 ft sheet.
Thick blanks
Oxy-fuel blanks up to 200 mm for machining and forging.
Plasma current and thickness
Swipe the table sideways to see all columns.
| Plasma current | Good-quality cut (edge start) | Production pierce | Typical work |
|---|---|---|---|
| 85 A | up to 20–25 mm | about 12–16 mm | Brackets, base plates |
| 100–105 A | up to 25–32 mm | about 16–20 mm | Fabrication shops |
| 120–125 A | up to 32–38 mm | about 20–25 mm | Thicker structural plate |
| 200 A | up to 50 mm | about 30–32 mm | Heavy plate on gantries |
| 300 A | up to 60 mm | about 40 mm | Heavy fabrication |
Typical guidance for mild steel. Stainless steel and aluminum cut thinner. Capacity differs between plasma brands, so we confirm it for the source on your quotation. CNC parts usually start with a pierce, which is roughly half to two thirds of the edge-start thickness.
What your workshop needs
- Electrical supply: 3-phase 380 V or your local industrial voltage; oxygen and fuel gas (acetylene or propane) for the oxy-fuel torch. Tell us your local voltage and frequency (50 or 60 Hz) before we build the machine.
- Clean, dry compressed air: an air compressor with a refrigerated dryer and filters. We give the flow and pressure for the plasma source you choose.
- A level concrete floor and space to load full sheets with a forklift or crane.
- Fume control: a water table or a down-draft table with an extraction fan, depending on the model.
- A Windows PC for nesting software such as FastCAM, to turn DXF drawings into cutting programs.
Shipping, installation and support
Free production layout
Send your parts list or shop drawing and our engineers suggest the machine size, plasma source and table layout before you order.
Packed for sea freight
Machines are packed for container shipping. We quote to your nearest port in South America, Africa or elsewhere and prepare the export documents.
Installation and training
Remote installation guidance and operator training are included. On-site commissioning can be arranged.
Remote diagnostics
Our team supports the control, the plasma source and the nesting software remotely, so most problems are solved without waiting for a visit.
Get a configuration and price
Send the material, the thickest plate or largest pipe you cut, your sheet or pipe size and how many hours a day the machine will run. An engineer replies with the right P1530 configuration, the options and a price delivered to your port.
Frequently asked questions
How thick can the P1530 cut?
Up to 40 mm steel with plasma, and 6 mm to 200 mm with the oxy-fuel torch.
What sheet size does it take?
1500 × 3000 mm (5 × 10 ft) plate, cut without re-sizing.
Which plasma brand is fitted?
A Hypertherm plasma system. We size the amperage to the thickest plate you cut with plasma.
Can oxy-fuel cut stainless steel or aluminum?
No. Oxy-fuel only cuts carbon and low-alloy steel. Use the plasma torch for stainless steel and aluminum.
When should I choose a gantry instead?
When your plate is wider than 1500 mm or longer than 3000 mm, or you want several torches cutting at once. See the G2040, G3060 and heavy-duty gantry machines.
Related machines and guides
Last updated 15 October 2026. Specifications are for standard configurations and can change with options; confirm on your quotation.